Saturday, May 29, 2010

Day 2 on our Journey from Torrance California to Alaska in a Robinson R22 18 May 2010

We woke up to nice weather, sunny with just a breeze. As they say, chamber of commerce weather. It was about 6:30am (Pacific Time) and time to get ready for another day of flying the little R22 helicopter north. I was hoping today would be a nice day and so far it was looking good outside. We went down and grabbed some continental breakfast the hotel provided and then checked out. We called Honeycutt Aviation at the airport where we parked the helicopter for the night and they were kind enough to come out and give us a ride back to the airport. I started the preflight and everything looked good except for the main rotor gearbox (transmission) fluid level.

R22 Main Rotor Gearbox Oil: Full, No Leaks

It should be full with no leaks like the photo above. We had no gearbox oil showing which meant it was low. Not good. The thing is we had the same problem with it when we picked it up at the Robinson Factory. The mechanics at the factory brought out more fluid and filled it up to the line before we left Torrance the day before, and the gearbox showed full at each fuel stop. For some reason this morning it was low again and not showing in the site glass. We couldn't see any leaks anywhere, and it's not normal for it to use up oil. Unlike an automobile engine, the main rotor transmission (gearbox) oil does not get used up, so if the level is going down over time there is probably a leak. That would not be typical: usually there is no leak and you never have to add oil. But this happened over night, which is out of the ordinary. We called Keith the owner at Alpine Air Alaska, he suggests we fly it to Redding, California where there is a service center for Robinsons. He felt there was enough oil to get us that far. Okay, that's easy for you to say. So we are off to Redding, and I’m hyper aware of any subtle changes in the helicopter’s performance, but nothing goes wrong and we get there in one piece. We call for fuel and let the fluid levels settle before we check them again. Strangely enough the main rotor gearbox oil level is full again. I've never seen this happen on any other R22 that I fly, this is strange. So we press on and the rest of the day the oil level in the site glass shows normal. We did pay close attention to the main rotor transmission chip and temperature detector lights for anything that may be going wrong. This phenomena happened each morning, the gearbox oil level would indicate low until after the first leg, then the oil would show normal again. This was the only abnormal anomaly that occurred with niner niner five zero seven on our whole trip. After a couple days I stopped worrying about it. So you're probably wondering what they did about the main rotor gearbox oil when we made it back to Alaska. Simple, they filled her to the brim and from what I hear she's fine now. Bizarre...
At Redding we make a decision to stay east of the Cascades. From the weather reports, and what we could see as we got closer to the Cascade Mountains, we take note that they are definitely loaded with clouds and bad weather on the west side. So we headed north hooked a right around Mount Shasta and then on to Klamath Falls, Oregon. Staying east of the Cascades would help us to avoid the bad weather. I was a little disappointed, mainly because I was hoping to follow the coast, but you do what you have to in order to get the helicopter from point A to B. It's sunny and we have a tail wind, it's always good to have a tail wind! The leg to Klamath Falls was pretty uneventful, except for the the terrain, we notice the elevation levels in general are getting higher, upwards to three and four thousand feet. The elevation is 4100 feet at Klamath Falls, but the little R22 does fine. I should note here that having an older aviation chart to navigate by bit us in the butt when it came to calling the tower. The old chart said the tower frequency was 118.3, no answer, after several tries someone came on the air and told us the new frequency was 133.975, thanks for that, but now I'm feeling a little stupid for having an old chart. We land, call for fuel on the Unicom frequency, 122.95. It's also time to get all the bugs off the windshield from flying through California. There's a lot of activity here; F-15's from the local Guard unit are flying sorties and apparently having exercises. One F-15 comes in drops his hook and catches the barrier. Fire trucks and emergency responder vehicles speed out to meet the F-15. Nothing is wrong, it's just an exercise, a practice drill, interesting to watch.

F-15 Strike Eagle

F-15 taxing behind our R22, Klamath Falls

We also notice, and on the other end of aviation's time spectrum, a B-17 bomber on the ramp just north of us. It's a real operating B-17. We can't resist and walk over to take a closer look. We see they are offering rides for 350 bucks and tours inside the bomber for something like 18 bucks. We don't have the time or money so we just look from the outside and take a few pictures, it was sure an awesome bomber to see up close. Feared by the Germans during WWII.

B-17 Flying Fortress

               The B-17 we saw in Klamath Falls

After refueling, cleaning the bugs off the bubble and doing a little site seeing we get in, start up, and get the main rotors up to operating speed. We then contact the tower and ask for a departure to the north from our present position. We are told to stand-by as F-15s are on their way in to land. After a few minutes we were given clearance and depart to the north, always north.

On our way to Madras, Oregon

We were on our way to Madras, Oregon. Not that we had this planned, but where we ended up based on the need for fuel. In fact, except for Canada where we didn't have much of a choice, our stops were not planned at all, except that we were generally heading to Oroville, Washington and overall basically heading north, these fuel stops were on the way, or at the end of each day where we simply ended up. We literally took it hour by hour. Why Oroville? Because this is where we had to, actually where we decided to cross the border and coordinate with US and Canadian Customs. I'll explain more about that when we get there. So, we head north and have a pretty good tail wind with some gusting, I believe something like 25 knots or so along this route of travel. I start feeling some strange forces on the helicopter when the winds are gusting from behind. It's not something I've ever really dealt with before in training. What happens is the gust from the rear wants to lift the nose of the helicopter, I have to fight these pressures by pushing forward on the cyclic and pulling up on the collective during these sudden gusts from the rear. After a few hours of this they become second nature to handle. There's something else about the little R22 that I never thought about during training, there is no hydraulics, it's direct linkage. So I'm feeling all the flight pressures all day long and this starts to wear on me, I have to learn to hold the controls in such a way that it doesn't strain my wrists. I also sat on the left side the whole trip in order to get used to the instructor's seat. Did I mention my butt was hurting? Hey, it's the price we pay to have fun!

How do helicopter controls work?

We eventually make it to Madras Oregon just north of Bend still fighting 20 knot winds, gusts, and turbulence, but they are tail winds so I'm happy about that and not complaining, we land to refuel. It's a pretty barren place, high desert and kind of brown, sage brush country. It sure feels good to get out and stretch. The wind is kind of hot and dry, again I'm not complaining because the winters are long here in Alaska and the warmth felt good. We refueled and took a bathroom break and we were ready for one more leg. We never knew exactly where we would end up each night. This night it turned out to be Wenatchee, Washington, apple country, a beautiful high desert little city near the Columbia River. I felt comfortable and wouldn't mind living there some day. We found a Comfort Inn and they sent out a taxi/shuttle for us. A little trick we learned; if you call the hotel and they send the taxi you don't have to pay for it, they are a service to the hotel. If we called the taxi we'd have to pay for it. I did not know that. The taxi driver was kind enough to explain to us how the whole system worked. The lady behind the desk was extremely courteous, it appears they make chocolate chip cookies each night but they had just run out. Darn, I guess we looked disappointed because about 15 minutes later there was a knock at the door, she had made a fresh batch of cookies just for us. Thank you for the cookies! We then found a nice little place to eat near the hotel called Prospector Pies. I ordered myself a hamburger and fries, one of the best burgers I've had in awhile. I would definitely go back. After that meal I was ready to hit the sack after flying the helicopter for 7.2 hours. The thing is you have to constantly fly a helicopter and concentrate every second which is mentally draining. An airplane can be trimmed out and will more or less fly itself. Let’s just say my landings were getting a little sloppy by the end of the day.

Me and the K-MAX, Wenatchee, WA


Hobbs schedule for the day:

Yuba County Airport, Marysville, CA (KMYV) - Redding Municipal Airport, CA (KRDD) 1.4 hours

Redding Municipal Airport, CA (KRDD) - Kingsley Field, Klamath Falls, OR (KLMT) 1.7 hours

Kingsley Field, Klamath Falls, OR (KLMT) - Madras Airport, OR (S33) 2.0 hours

Madras Airport, OR (S33) - Pangborn Memorial Airport, Wenatchee, WA (KEAT) 2.1 hours

Total 7.2 hours 515 NM's

Thursday, May 27, 2010

Day 1 on our Journey from Torrance California to Alaska in a Robinson R22 17 May 2010

Robinson Helicopter Factory

Our journey began here at Zamperini Airport in Torrance, California at the Robinson Helicopter Factory.  If you're interested in seeing the inside of the factory here's a nice little slide show by a pilot (Paul Cantrell) who attended the Robinson Safety Course in 2006.

Pretty funny now looking back on this day; one of the test pilots there at the factory wanted to know who hit us over the head in order to get us to fly an R22 that far north to Alaska. Little did I know what the next five days would hold for me, at the time I was ready to do whatever it took to get that little R22 back up to Alaska. Let the journey begin...

If you click on SkyVector.com link below you will see the LA West helicopter chart and Zamperini Field in Torrance, California where we started from. I was feeling apprehensive about getting out of the L.A. area and I knew this was going to be complicated dealing with Air Traffic Control (ATC) especially getting through LAX and the Class B airspace.

Flight Planning at SkyVector.com
Helicopter Route Chart-Los Angeles 

The marine layer was set in all along the coast and it was a gray day with low ceilings. This was not going to make it easy for us on our first leg out of Southern California. We wanted to follow the coast up to Washington but the whole coast was completely socked in making that route nearly impossible to navigate, so we chose the California Central Valley instead.
Torrance gave us clearance to proceed with the prevailing winds favoring runway 29 with a westerly heading to the coast. We transitioned NW up the shoreline with the first landmark being Redondo Harbor. We contacted LAX tower and asked for a shoreline transition through their Class B airspace. I later found out we should have contacted Heli control on 119.8 but ATC was friendly and worked with us newbie’s trying to get the hell out of the area. So, LAX Tower gave us clearance at or below 150' along the shoreline transitioning LAX airspace. It was weird because we had jumbo jets departing right over our flight path. You can see the Heli routes and dark purple/blue on this chart. We saw a lot of piers and stayed out beyond those and were basically skimming above the ocean at 75 to a 100 feet just west of the LAX runways. Cool!
We reported Marina Del Rey and  I sighed a breath of relief, I had just experienced a  Class B (LAX) airspace transition along the shoreline, so far so good.  We continued along the shoreline and reported to Santa Monica Tower requesting a transition through their Class D airspace along the shoreline. Request approved, we had no problems getting through their airspace.  I do remember seeing Venice Beach along here also.  The next landmark was the Santa Monica Pier which meant it was time to turn north and intercept the 405 to the  I-5.

The Santa Monica Pier as we fly by just after passing LAX

Our goal here was to try and make California’s Central Valley which we new was clear and sunny.  The day before flying in on Alaska Airlines I could see the Valley was clear and the coast line was socked in completely with the marine layer. Weather reports were still showing this to be true. We found the 405 and proceeded north up through the Sepulveda Pass. Now remember the ceilings are low and visibility is only about 2 miles and here is when things started getting a little dicey heading up the pass. We know we have intercepted the 405 because we see the Getty Center a major landmark, pretty cool to see from the air.

The Getty Center as we pass by on our way up Sepulveda Canyon

Sepulveda Pass on a nice day

Working our way up Sepulveda Pass, N bound 405; Photos taken by Corey

Crap, the ceilings start dropping, actually the terrain is rising, as we proceed up the Sepulveda Pass and we can't quite get above the tops of the Santa Monica Mountains as we near the Van Nuys Airport. This is not looking good because now the visibility is down to about a mile as we pass Mulholland Drive. At least we can see through to lighter skies as we look north beyond the pass. And then they appeared, transmission towers with power lines stretching across the canyon, can things get any worse. So what seemed like forever dodging low lying clouds and power lines we finally make it over the pass and see the Van Nuys Airport looming ahead on our left. We make a call to the tower and again are informed we need to be talking to Heli Control on 119.0 since we are following a heli route north up the 405, we switch over to 119.0 and are cleared through the area. As I near the Van Nuys Airport I'm straining to see the runways. One in specific I want to see is the famous 16R; I see it and smile to myself. It's famous and has a lot of history. If you've never seen the documentary "One Six Right" do yourself a favor and go watch it, you won't be disappointed.

Passing by Van Nuys Airport (VNY) out there in the distance

We press on north and finally see I-5 and follow that for a while; things are still not looking good weather wise, and we decide to head further east and follow 14 known as the Antelope Valley Freeway. We are still desperately trying to get out of the coastal marine layer and bad weather. We have one more pass to get over at the junction of I-5 and 14 called the Newhall Pass, ceilings are still low and we have more transmission power lines to get over but things are starting to look better the farther east we get, thank God. We are now headed towards the Lancaster, Palmdale area and finally clearing the weather and almost in the Valley but now the winds are kicking up to about 28 knots giving us quartering tail winds, which is good, but it's turbulent. We are low on fuel and make a decision to land at General Fox. We are cleared through Palmdale Regional Plant 42 and are given clearance to land at General Fox just southwest of Edwards AFB. Whew! That was the most intense 1.3 hours I've ever spent in my limited career flying helicopters and probably the most intense leg on the whole journey up to Alaska. Lesson learned; I won't push the MVFR weather when trying to get through mountains and passes ever again. I don't care how long I have to wait!
The rest of the day we headed north through California’s Central Valley basically following 99 passing through Bakersfield, Visalia, and eventually landing at Fresno-Chandler Municipal Airport for fuel, and then on to Yuba County Airport, Marysville California near Beal AFB where we stayed overnight. We landed in the dark around 8 PM. I was done, cooked! I was thankful we made it this far. My butt was hurting, let’s just say the little R22 seats are not conducive to comfort. I should mention that while we were landing at the Yuba County Airport another helicopter was landing also, a Reach EMS helicopter. The pilot, I believe his name was Pat, was kind enough to give us a ride into the little town of Linda and took us to a Comfort Inn. In fact during the whole journey everyone was extremely helpful all the way up to Alaska. We logged 5.6 hours on the hobbs and traveled approximately 364 nautical miles or 419 statute miles on the first day. What a day! I was wondering what the next day would hold for us as I laid there in bed trying to sleep still hyped up on adrenaline.
One thing I learned about the Yuba County area, they grow rice here, tons of rice, apparently producing up to 95% of the rice grown in the state and 80% of the rice grown in the country. It was amazing how the rice fields seemed to never end.

Hobbs schedule for the day:

Zamperini Field, Torrance, CA, Robinson Helicopters (KTOA) - General Wm J Fox Airfield, Lancaster, CA (KWJF)  1.3 hours

General Wm J Fox Airfield, Lancaster, CA (KWJF) - Fresno Chandler Executive Airport, CA (KFCH) 2.3 hours

Fresno Chandler Executive Airport, CA (KFCH) - Yuba County Airport, Marysville, CA (KMYV) 2.0 hours

Total 5.6 hours 364 NM's

Tuesday, May 25, 2010

Mission Accomplished! Ferry Flight 17-21 May 2010 - Robinson R22 helicopter

Ferry Flight - Torrance California to Birchwood Alaska in a Robinson R22

The ferry flight took us 34.8 hours of flying and our flight path was approximately 2500 nautical miles over 5 days of flying. If you click on each helicopter it will give you a little description of that particular stop. We did have some MVFR weather on our first leg out of Torrance, California and again around the Fort St. John and Fort Nelson, BC, Canada areas. Other than that we fought quite a bit of turbulence in most areas. Whew! What an adventure. As I get a little more time I'll try and shed some more light on our trip.


View Ferry Flight 17-21 May 2010 Robinson R22 helicopter in a larger map


The newly rebuilt R22 we brought up from Torrance, California
She ran like a champ!

Friday, May 14, 2010

On our way to ferry an R22 from Torrance, California to Birchwood, Alaska

We are on our way down to Torrance, California to ferry one of our R22 helicopters (N767VC) that’s been rebuilt back up to Birchwood, Alaska. It's going to be one hell of an adventure! Let’s hope its uneventful and we pull it off without a hitch. I'll be doing the trip with Corey one of my instructors. And who knows, I might even learn something. It'll be a chance for me to put everything I've learned in the last two years of helicopter training to the test. I'm taking a camera, and if possible will take a few photos along the way to share when I get back. As some of you know there’s not much room in the R22 so all I'm taking is a small little black back pack that will fit under the seat. We'll be roughing it for sure, but the goal is to get the helicopter and us back up here to Alaska in one piece. Our biggest obstacle will be the weather!

Old 7VC that's been rebuilt, rumor has it she's now red with a new registration # 99507; she was a good old bird!

N767VC, I soloed in this ship! I'm curious to see how she's going to look after the rebuild.

According to Google we are looking at approximately 4,300 miles. Our route will depend on the weather coming up through California, Oregon and Washington but more than likely we'll follow I-5 north and enter Canada at Kelowna, BC. Canada can be a desolate place and staying near the main road (ALCAN HWY) is safer in my book. Our route will follow Williams Lake, BC; Prince George, BC; Dawson Creek, BC; Fort St. John, BC; Fort Nelson, BC; Watson Lake, YT; Whitehorse, YT; Haines Junction, YT; Beaver Creek, YT; Northway Junction, AK; Tok, AK; Glenallen, AK; and then on to Birchwood, AK. Of course we can fly as the crow fly’s and straighten out all the curves :-).  I'm glad we're ferrying the helicopter with summer just around the corner, and as we approach Alaska the days will be longer with plenty of daylight. Wish us luck!

Monday, May 3, 2010

Aviation Trade Show - Anchorage, Alaska May 1-2, 2010

Organizers believe about 30,000 people attended this year's event, held in the FedEx hangar at Ted Stevens Anchorage International Airport. What a fun day! I spent the afternoon on Saturday helping Alpine Air Alaska. We had a static display of one of our R44s set up next to Alpine Air's booth. It was my job to stand out by the helicopter and answer questions and keep the kids from playing on it. I answered so many questions my voice went horse.
Merit Apparel, who sells helicopter flight helmets from Vero Beach, Florida was also in attendance. I jumped on the opportunity to get fitted for a MSA Gallet flight helmet. It's not that I need a flight helmet right now, but in the future if I do, Merit Apparel will have my measurements if the need ever comes up.

Wearing the MSA Gallet flight helmet LH 250

Alpine Air Alaska R44 Static Display 

The Bell 407 


Mosquito XEL Kit Helicopter that was on display at the trade show

They also had the display of the little kit helicopter known as the "Mosquito". Chester Godin sells the kits out of Big Lake, Alaska; Alaska Helicopter Sales. I gave this little thing a test run about 7 months ago in Palmer, Alaska. Here's what I said back then (September 18, 2009) As we were heading home I noticed a Mosquito, not on the windshield, on the ground! I just learned about them, so we pulled over to talk with the guy. A week later we went back and I flew her. My objective was to feel it hover;  first I had to get used to the throttle and keep the rotor RPM's in the green. Second was to get the machine light on the skids... slowly I pulled into a hover, this took some practice and several pick-ups and set-downs. After a few of these I started to get a feel for this tiny helicopter. The nose wanted to pop up when picking up and setting down. The throttle is the opposite of an R-22, there is no correlator or governor, it’s not what I’m used to and that made it tuff to keep it coordinated. 10 minutes was enough for my first flight in the XEL kit helicopter.
Here's the video...